specifcations cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type tha,thinpack, aluminum electrolytic capacitor, 85 oc highlights - 8.2 mm profle - very high energy density (up to 1.1 j/cc) - 3000 hr life @ 85 oc - reach and rohs compliant temperature range C55 c to +85 c 300 vdc; -40 oc to 85 oc 350 vdc rated voltage range 10 vdc to 450 vdc capacitance range 60 f to 18000 f capacitance tolerance 20% leakage current 0.002 cv a, @ 25 c and 5 mins. at rated voltage ripple current multipliers low temperature characteristics impedance ratio: z C55 ?c M z +25 ?c @120 hz 10 (5 - 20 vdc), 3 (25 - 300 vdc) z -40 oc /z +25 oc @120 hz 10 (350 vdc) dc life test 3000 h @ rated voltage at 85 c ? capacitance 20% (<50 vdc) ? capacitance 10% (50 vdc) esr 200% of limit dcl 100% of limit shelf life test 5 yrs @ 40 oc capacitance 100% of limit esr 100% of limit dcl 0.004 cv a ambient temperature multipliers temp 45 55 65 75 85 0-300 vdc 1.30 1.25 1.00 0.70 0.20 301-450 vdc 1.15 1.10 1.00 0.60 0.20 frequency multipliers rated vdc/freq 50 60 120 360 1000 5000 20000 10-35 0.72 0.77 1.00 1.06 1.06 1.10 1.10 36-60 0.70 0.75 1.00 1.06 1.10 1.20 1.20 61-100 0.70 0.75 1.00 1.06 1.10 1.30 1.30 101-300 0.70 0.75 1.00 1.20 1.45 1.70 1.70 301-450 0.70 0.75 1.00 1.20 1.45 1.80 1.80 at 8.2 mm thin, type tha thinpack ofers the highest energy density available in a low profle aluminum electrolytic. its ideal for the lowest profle circuits where high capacitance is needed for bulk storage. look to type tha to replace arrays of smt solid tantalum or aluminum electrolytic capacitors. high energy density, reach and rohs compliant ambient air temperature multipliers (no heat sink) air velocity m/sec 0.25 1.00 2.50 5.00 ripple current multiplier 1.00 1.20 1.40 1.50
cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 vibration mounting: vibration capability is dependent upon mounting restraint. mil-std-202, meth. 204, sine swept, iec 60068-2-6 all sizes = 10g mil-std-202, meth. 204, condition h vibration test level the specimens, while deenergized or operating under the load conditions specifed, shall be subjected to the vibration amplitude, frequency range, and duration specifed for each case size. amplitude the specimens shall be subjected to a simple harmonic motion having an amplitude of either 0.06-inch double amplitude (maximum total excursion) or peak level specifed above, whichever is less. the tolerance on vibration amplitude shall be 10 percent. frequency range the vibration frequency shall be varied logarithmically between the approximate limits of 10 to 2,000 hz. sweep time and duration the entire frequency range of 10 to 2,000 hz and return to 10 hz shall be traversed in 20 minutes. this cycle shall be performed 12 times in each of three mutually perpendicular directions (total of 36 times), so that the motion shall be applied for a total period of approximately 12 hours. interruptions are permitted provided the requirements for rate of change and test duration are met. thermal resistance thermal resistance (cw) by case length of sides heatsinked insulation 36.4 (mm) 45.9 (mm) 53.8 (mm) 66.5 (mm) n i bare can 5.42 4.27 3.65 2.96 polyester 6.60 5.20 4.44 3.60 both sides bare can 4.36 3.41 2.90 2.34 polyester 4.95 3.87 3.30 2.66 typical weight case aa - 14g, case ab - 16g, case ac - 18g, case ad - 20g terminals 20 awg copper wire with tin electroplate, 15 amps max case material aluminum ripple current capability the max ripple current capability is set by the target core temperature of 85 oc. the peak to peak ac must be less than vr/5. air cooled the ripple currents in the ratings tables are for 65 oc ambient temperatures. heatsink cooled temperature rise from the hottest internal spot, the core, to ambient air is ?t = i 2 (max esr)(cc + ca), recommended max ?t of 20 oc where cc is the thermal resistance from core to case and ca from case to ambient. to calculate maximum ripple capability with the tha attached to a heatsink use the maximum core temperature and the values for cc. example as an illustration, suppose you operate an noninsulated tha132m060aa0c in 65 oc air and attach it to a commercial heatsink with a free-air thermal resistance of 2.7 oc/w. use a good thermal grease between the capacitor and the heatsink, and the total thermal resistance is 2.7 + 5.42 or 8.12 o c/w. the power which would heat the core to 85 c is (85 - 65)/8.12 or 2.46 w. for an esr of 117 m, 2.46 w equates to a ripple current of 4.58 a. type tha,thinpack, aluminum electrolytic capacitor, 85 oc
part numbering system outline drawing cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 tha 412 m 025 aa 0 c type capacitance tolerance rated voltage case code insulation mounting style tha 322 =3200 f 222 = 2200 f 162 = 1600 f m= 20% 025 = 25 vdc 075 = 75 vdc 150 = 150 vdc 200 = 200 vdc aa = 36.4 mm ab = 45.9 mm ac = 53.8 mm ad = 66.5 mm 0 = bare can 1 = polywrap c = two leads l0.5 mm 30mm min 24.2mm0.3 mm 10mm 2mm max 8.2mm0.3 mm 0.82mm dia 20 awg leads (typ) type tha,thinpack, aluminum electrolytic capacitor, 85 oc style c: no tabs note: the polyester tape wrap may add up to 0.020 inches to the thickness and width of the capacitor. 10 mm 0.25 mm
cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 ratings voltage cap (f) catalog part number length esr max 25 c () 120 hz 20 khz ripple (a) ambient @ 65c 120 hz 20 khz 10 vdc @ 85 c 12 vdc surge @ 25 c 8500 tha852m010aa0c 36.4 0.12 0.09 1.90 2.09 11000 tha113m010ab0c 45.9 0.08 0.07 1.90 2.09 14000 tha143m010ac0c 53.8 0.07 0.06 2.50 2.75 18000 tha183m010ad0c 66.5 0.05 0.04 3.30 3.63 16 vdc @ 85 c 19.2 vdc surge @ 25 c 6300 tha632m016aa0c 36.4 0.12 0.09 1.90 2.09 8700 tha872m016ab0c 45.9 0.08 0.07 2.10 2.31 10000 tha103m016ac0c 53.8 0.07 0.06 2.50 2.75 13000 tha133m016ad0c 66.5 0.05 0.04 3.30 3.63 20 vdc @ 85 c 24 vdc surge @ 25 c 5000 tha502m020aa0c 36.4 0.12 0.09 1.90 2.09 7000 tha702m020ab0c 45.9 0.08 0.07 2.10 2.31 8600 tha862m020ac0c 53.8 0.07 0.06 2.50 2.75 11000 tha113m020ad0c 66.5 0.05 0.04 3.30 3.63 25 vdc @ 85 c 30 vdc surge @ 25 c 4100 tha412m025aa0c 36.4 0.12 0.09 1.90 2.09 5700 tha572m025ab0c 45.9 0.08 0.07 2.40 2.64 7000 tha702m025ac0c 53.8 0.07 0.06 2.50 2.75 9000 tha902m025ad0c 66.5 0.05 0.04 3.30 3.30 30 vdc @ 85 c 36 vdc surge @ 25 c 3300 tha332m030aa0c 36.4 0.12 0.09 1.90 2.09 4600 tha462m030ab0c 45.9 0.08 0.07 2.40 2.64 5700 tha572m030ac0c 53.8 0.07 0.06 2.80 3.08 7400 tha742m030ad0c 66.5 0.05 0.04 3.30 3.63 35 vdc @ 85 c 42 vdc surge @ 25 c 2600 tha262m035aa0c 36.4 0.12 0.09 1.90 2.09 3600 tha362m035ab0c 45.9 0.08 0.07 2.40 2.64 4400 tha442m035ac0c 53.8 0.07 0.06 2.80 3.08 5800 tha582m035ad0c 66.5 0.05 0.04 3.50 3.85 40 vdc @ 85 c 48 vdc surge @ 25 c 2300 tha232m040aa0c 36.4 0.12 0.09 1.70 2.04 3200 tha322m040ab0c 45.9 0.08 0.07 2.20 2.64 4000 tha402m040ac0c 53.8 0.07 0.06 2.50 3.00 5200 tha522m040ad0c 66.5 0.05 0.04 3.00 3.60 50 vdc @ 85 c 60 vdc surge @ 25 c 1600 tha162m050aa0c 36.4 0.12 0.09 1.70 2.04 2200 tha222m050ab0c 45.9 0.08 0.07 2.20 2.64 2700 tha272m050ac0c 53.8 0.07 0.06 2.50 3.00 3500 tha352m050ad0c 66.5 0.05 0.04 2.90 3.48 60 vdc @ 85 c 72 vdc surge @ 25 c 1300 tha132m060aa0c 36.4 0.12 0.09 1.70 2.04 1800 tha182m060ab0c 45.9 0.08 0.07 2.20 2.64 2300 tha232m060ac0c 53.8 0.07 0.06 2.50 3.00 3000 tha302m060ad0c 66.5 0.05 0.04 3.30 3.96 75 vdc @ 85 c 90 vdc surge @ 25 c 730 tha731m075aa0c 36.4 0.29 0.19 1.10 1.43 1000 THA102M075AB0C 45.9 0.21 0.14 1.40 1.82 1200 tha122m075ac0c 53.8 0.17 0.11 1.60 2.08 1600 tha162m075ad0c 66.5 0.13 0.09 2.00 2.60 100 vdc @ 85 c 120 vdc surge @ 25 c 580 tha581m100aa0c 36.4 0.29 0.19 1.10 1.43 800 tha801m100ab0c 45.9 0.21 0.14 1.40 1.82 980 tha981m100ac0c 53.8 0.17 0.11 1.60 2.08 1200 tha122m100ad0c 66.5 0.13 0.09 2.00 2.60 type tha,thinpack, aluminum electrolytic capacitor, 85 oc
voltage cap (f) catalog part number length esr max 25 c () 120 hz 20 khz ripple (a) ambient @ 65c 120 hz 20 khz 150 vdc @ 85 c 180 vdc surge @ 25 c 330 tha331m150aa0c 36.4 0.80 0.40 0.60 1.02 450 tha451m150ab0c 45.9 0.58 0.29 0.80 1.36 560 tha561m150ac0c 53.8 0.47 0.24 0.90 1.53 730 tha731m150ad0c 66.5 0.37 0.18 1.20 2.04 200 vdc @ 85 c 240 vdc surge @ 25 c 170 tha171m200aa0c 36.4 0.90 0.45 0.60 1.02 230 tha231m200ab0c 45.9 0.65 0.33 0.80 1.36 280 tha281m200ac0c 53.8 0.53 0.27 0.90 1.53 370 tha371m200ad0c 66.5 0.41 0.21 1.10 1.87 250 vdc @ 85 c 300 vdc surge @ 25 c 140 tha141m250aa0c 36.4 0.90 0.45 0.60 1.02 190 tha191m250ab0c 45.9 0.65 0.33 0.80 1.36 240 tha241m250ac0c 53.8 0.53 0.27 0.90 1.53 310 tha311m250ad0c 66.5 0.41 0.21 1.10 1.87 300 vdc @ 85 c 350 vdc surge @ 25 c 110 tha111m300aa0c 36.4 0.90 0.45 0.60 1.02 160 tha161m300ab0c 45.9 0.65 0.33 0.80 1.36 190 tha191m300ac0c 53.8 0.53 0.27 0.90 1.53 250 tha251m300ad0c 66.5 0.41 0.21 1.10 1.87 350 vdc @ 85 c 400 vdc surge @ 25 c 90 tha900m350aa0c 36.4 2.45 1.18 0.40 0.72 130 tha131m350ab0c 45.9 1.78 0.85 0.50 0.90 160 tha161m350ac0c 53.8 1.45 0.70 0.60 1.08 210 tha211m350ad0c 66.5 1.12 0.54 0.80 1.44 400 vdc @ 85 c 450 vdc surge @ 25 c 80 tha800m400aa0c 36.4 2.45 1.18 0.40 0.72 110 tha111m400ab0c 45.9 1.78 0.85 0.50 0.90 140 tha141m400ac0c 53.8 1.45 0.70 0.60 1.08 180 tha181m400ad0c 66.5 1.12 0.54 0.80 1.44 450 vdc @ 85 c 500 vdc surge @ 25 c 60 tha600m450aa0c 36.4 2.45 1.18 0.40 0.72 90 tha900m450ab0c 45.9 1.78 0.85 0.50 0.90 110 tha111m450ac0c 53.8 1.45 0.70 0.60 1.08 140 tha141m450ad0c 66.5 1.12 0.54 0.80 1.44 cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type tha,thinpack, aluminum electrolytic capacitor, 85 oc 1 10 100 1000 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 expected operating life, kh rated ripple - current multiple type tha operating life in kilohours vs ripple current 55 c 65 c 75 c 85 c typical erforance curves rated ripple current multiple type tha operating life in kilohours vs. ripple current
typical performance curves cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type tha,thinpack, aluminum electrolytic capacitor, 85 oc tha272m060ac0c 0.01 0.1 1.0 10.0 10 100 1000 10000 100000 1000000 |z| ( ) frequency (hz) |z| vs. frequency & temperature 85 65 45 25 0 -20 -40 -55 0.01 0.1 1.0 10 100 1000 10000 100000 1000000 esr ( ) frequency (hz) esr vs. frequency & temp 85 65 45 25 0 -20 -40 -55 0.0 500.0 1000.0 1500.0 2000.0 2500.0 3000.0 10 100 1000 10000 100000 1000000 capacitance (f) frequency (hz) capacitance vs. frequency & temperature 85 65 45 25 0 -20 -40 -55
notice and disclaimer: all product drawings, descriptions, specifcations, statements, information and data (collectively, the information) in this datasheet or other publication are subject to change. the customer is responsible for checking, confrming and verifying the extent to which the information con - tained in this datasheet or other publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without any guaran - tee, warranty, representation or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on the knowledge that the cornell dubilier company providing such statements (cornell dubilier) has of operating conditions that such cornell dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representa - tion regarding any such matter C and cornell dubilier specifcally and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specifc customer application, use, storage, transportation, or operating environment. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by cornell dubilier with reference to the use of any cornell dubilier products is given gratis (unless otherwise specifed by cornell dubilier), and cornell dubilier assumes no obligation or liability for the advice given or results obtained. although cornell dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indi - cated in such warnings, cautions and notes, or that other safety measures may not be required.
|
